Simulate lighting setups on your computer with Set.A.Light 3D


If you’re looking to photograph a model, it’s great to have an idea of ​​the correct lighting configuration. Experimenting with the model in front of your camera may not be the best time to do so. With the software set.a.light.3D it is possible to simulate every imaginable lighting setup.

I don’t have my own studio. But sometimes I turn my living room into a simple studio. I call it my living room studio and it’s perfect for some simple shots. For this living room studio, I have two Profoto B10 lights up with different modifiers and two Profoto A1 flash units.

It’s easy to use a simple but effective Rembrandt lighting setup, but not always. Sometimes it’s nice to use a completely different lighting setup. Having a good idea of ​​the right lighting configuration is, in my opinion, crucial for a successful shoot. It doesn’t work so well for me to try different light positions and modifiers when the model is in front of my camera.

While there’s nothing wrong with fine-tuning the location of the lights, I’d rather have a rough idea of ​​where to place the lights with the appropriate modifier. When you own a real studio, you have plenty of opportunities to try new things. There is less pressure to perform. If you don’t have a studio, like me, it often depends on when you have one available or when you are temporarily turning your living room into a studio.

There were times when I reused the familiar Rembrandt lighting setup when the ideas I had didn’t work. On these occasions I played it safe as changing the entire setup takes a lot of time and effort, especially when I’m not sure the other idea will work. It was very frustrating at times until I happened upon set.a.light.3D.

First I used the website Lighting diagrams. This online program can be used to create lighting diagrams, which can also be found in various articles on the Internet. However, these diagrams do not help me to visualize the result of a lighting setup. Fortunately, set.a.light.3D from the Elixxier software offers this possibility.

The program makes it possible to create every imaginable lighting setup. It is able to simulate the result. Any type of light is available and it is also possible to choose a virtual model. You can also change the model’s pose, clothes, and appearance.

Just drag and drop the lights you want to use or create your own. Change the settings for camera height, focal length, and exposure. Set the flash output and try out the effects of various modifiers. The studio can be viewed in 3D and you can rotate the view to see your studio from any angle. A lighting diagram and a simulation of your lighting setup are available.

I downloaded a trial version and experimented with the program. I tried a few lighting setups for the scheduled shoot. The great thing about set.a.light.3D is the realistic simulation of the light output and the shadows on the model. It also takes into account the effects of the walls, ceiling and floor when you adjust the dimensions of your virtual studio to match the real studio.

By creating a lighting setup in set.a.light. In 3D, I was able to find the right setup for my shoot without having to experiment with the lights in the studio while the model waited. I could place the lights according to the simulation to get the results I want.

The first attempt was for a normal but small studio. I tried set.a.light 3D also for my living room studio. I discovered how much of an impact the walls and ceiling had on the light by simulating the shoot. That way, I was ready to use a collapsible black background to cover a white wall to remove the reflectivity.

I think a program like set.a.light 3D is perfect for the beginning studio photographer. You can visualize the result of placing lights and light modifiers. It shows you how much walls, ceilings and floors influence your result. It’s easy to experiment with a lighting setup in this simulation program before using it in real life.

Perhaps the more experienced studio photographer needs such a program less, but I could be wrong.

I find set.a.light.3D very valuable software. There are two versions available. A basic version can be purchased for $ 79 and the studio version for $ 154. Given all the possibilities, I think these prices are very reasonable. You can test the software for 15 days without any restrictions. It is available for both Microsoft Windows and Mac.

I bought the studio version with my own hard earned cash. I have no relationship with Elixxier in any way and my opinion about this program is based on my own experience.

What do you think of set.a.light.3D? Did you know about this program or are you already using it? Please share your experience in the comments below. I would also like to invite you to share your thoughts on this software and how useful you find it. I look forward to your reply.

Source link


Leave A Reply